← Back to Tutorials
HARIMAU3D · PRINTER TUTORIALS

Flashforge AD5X
Getting Started.

From unboxing to your first successful print and beyond. Follow our step-by-step beginner guide, explore recommended filament profiles and learn how to get more out of your AD5X.

YOUR LEARNING JOURNEY

Getting Started with Your AD5X

New to 3D printing? Follow these four steps in order to set up your printer, complete your first print and become familiar with the AD5X.

STEP 01

Unbox & Complete Your First Print

Follow the official Quick Start Guide to unbox, assemble and set up your AD5X. Complete the initial calibration, load your filament and finish your first test print before moving on to the next step.

Before You Continue
Make sure your printer is fully assembled, calibrated and able to complete its first test print successfully.
STEP 03

Explore the User Manual

Get to know your AD5X better. Explore the official Flashforge Wiki for more information about printer features, settings, everyday operation and useful printing instructions.

STEP 04

Maintenance & Troubleshooting

Running into an issue with your AD5X? Refer to the official maintenance guide for common troubleshooting procedures, routine maintenance and component replacement instructions.

BONUS SETUP GUIDE

Install Your AD5X Camera

Your AD5X purchase from HariMau3D includes a complimentary camera. Follow our camera installation tutorial to install and set up your camera, so you can monitor your prints remotely.

Installation Reminder
Turn off and unplug your AD5X before installing the camera. Follow the installation video carefully and make sure all connections are secure before turning the printer back on.
WATCH CAMERA INSTALLATION ↗
TESTED BY HARIMAU3D

What Can Your AD5X Print?

The following materials have been tested by HariMau3D on the Flashforge AD5X. Use these recommended filament profiles and settings as your starting point in Flash Studio. Explore our tested filaments using the product links below.

Material Recommended Profile Settings Shop Filament
PLA HariMau3D PLA Basic Generic PLA Profile Default profile settings Shop PLA ↗
PETG HariMau3D PETG Basic Generic PETG Profile Default profile settings Shop PETG ↗
ABS HariMau3D ABS Basic Generic ABS Profile Default profile settings Shop ABS ↗
ASA HariMau3D ASA Basic Generic ABS Profile Bed: 110°C Override bed temperature Shop ASA ↗
← Swipe horizontally to view all material settings and product links. →

TPU Basic 95A

Direct Feed · No IFS

The AD5X can also print HariMau3D TPU Basic 95A flexible filament using our Top Spool Holder (TSH). TPU must be fed directly to the extruder instead of passing through the IFS.

1
Download and print the AD5X Top Spool Holder from our FREE STL page.
2
Install the Top Spool Holder on your AD5X and place your TPU spool on the holder.
3
Feed the TPU filament directly to the extruder without using the IFS.
4
Select a suitable TPU profile in Flash Studio and start printing.
Important: Do not feed TPU 95A through the IFS. Always use the direct-feed method when printing our TPU Basic 95A on the AD5X.
Good to Know: HariMau3D ABS Basic and ASA Basic have been successfully printed on the AD5X without an enclosure. See our Essential Printing Tips below for recommended printing conditions and first-layer calibration.
PRACTICAL TIPS FROM HARIMAU3D

Essential Printing Tips

Get better results from your AD5X with these practical tips based on our own printing experience and material testing.

TIP 01 · ABS & ASA

Printing ABS & ASA Without an Enclosure

Both HariMau3D ABS Basic and ASA Basic have been successfully tested on the Flashforge AD5X without an enclosure.

You can print these materials on your standard open-frame AD5X by keeping the printing environment stable and avoiding direct drafts.

✓
Avoid Direct Airflow Make sure that fans or air conditioners are not blowing directly onto your printer or printed model.
✓
Maintain a Stable Room Temperature Keep the surrounding temperature as stable as possible throughout the print. Avoid sudden or significant temperature changes.
✓
Use the Recommended Filament Profile Use the Generic ABS profile for our ABS Basic. For our ASA Basic, use the Generic ABS profile with the bed temperature set to 110°C.
✓
Ensure Proper Ventilation Print ABS and ASA in an adequately ventilated area with appropriate emission control. Arrange ventilation so that air does not blow directly onto the printer. Avoid printing these materials in poorly ventilated living or sleeping areas.
Tested Without an Enclosure
An enclosure is not required under the printing conditions we have tested with our ABS Basic and ASA Basic filaments. Larger models and certain geometries may be more sensitive to warping. Results may vary depending on the model and printing environment.
TIP 02 · FIRST LAYER CALIBRATION

First Layer Gaps? Adjust Your Z Offset.

If you notice visible gaps between adjacent lines on the first layer, the nozzle may be slightly too far from the build plate.

Before changing your filament flow rate or adding a Z Offset in your slicer, try adjusting the Z Offset directly on the AD5X.

Nozzle Too High

Individual lines remain separated, leaving visible gaps on the first layer.

Correct Z Offset

Adjacent lines join smoothly to form an even, continuous first layer without gaps.

200 × 200 mm
0.2 mm thickness
FREE CALIBRATION MODEL

First Layer Test – 200 × 200 mm

Download our single-layer calibration model to help you check your AD5X first layer and adjust the Z Offset. The large printing surface gives you enough time to observe the extrusion lines and make adjustments while the printer is printing.

STL FILE 200 × 200 mm SINGLE LAYER 0.2 mm
DOWNLOAD FIRST LAYER TEST STL ↓

Recommended Test Settings

Material HariMau3D PLA Basic
Filament Profile Generic PLA
First Layer Height 0.2 mm
Layer Height 0.2 mm
Model Dimensions 200 × 200 × 0.2 mm
Brim / Skirt Off
Expected Layers 1 Layer
Before Printing:
Import the STL into Flash Studio and make sure the model is lying flat on the build plate. Check the sliced preview to confirm that the model consists of only one layer. The model covers a large portion of the AD5X build plate, so make sure no brim, skirt or other additional printing features extend outside the printable area.

How to Adjust Your Z Offset

1
Start Printing the First Layer Test You can adjust the Z Offset while printing any model. However, we recommend using our 200 × 200 mm First Layer Test STL because its large, flat surface gives you enough time to observe and adjust the extrusion lines.
2
Open the Printing Settings While the printer is printing the first layer, tap the Settings icon at the bottom-right corner of the AD5X main printing screen.
3
Adjust the Z Offset If there are gaps between the first-layer lines, gradually adjust the Z Offset to bring the nozzle closer to the build plate. Make small adjustments at a time, using the smallest available increment. Observe the newly printed lines before adjusting again.
4
Check Your First Layer Continue adjusting until the gaps between adjacent lines disappear and the first layer looks smooth and consistent. Do not lower the nozzle too much. If you notice excessive squishing, rough ridges or nozzle scraping, move the nozzle slightly farther away from the build plate.
5
Keep the Correct Z Offset Once the correct height is achieved, leave the adjusted Z Offset in the printer. Based on our AD5X testing, the printer retains this adjustment for subsequent prints. You do not need to add a separate Z Offset to every model in your slicer.
Adjust Once. Use for Subsequent Prints.
Once your AD5X is correctly calibrated, keep the Z Offset adjustment on the printer itself. There is no need to print the calibration model before every normal print or apply an additional Z Offset in Flash Studio. Avoid applying the same correction in both the printer and slicer, as this may result in the nozzle being too close to the build plate.

If you replace the nozzle, change the build plate, reset the printer or notice changes in first-layer quality, check the Z Offset again and adjust it if necessary. If gaps persist despite a correct Z Offset, check your filament flow, extrusion and build plate condition.

KEEP LEARNING

Level Up Your 3D Printing Skills

Finished our beginner guide? Explore more techniques, practical tips and useful skills to get more out of your 3D printer.

PRINTING KNOWLEDGE

More Printing Skills 01

Explore additional 3D printing techniques and practical knowledge.

PRINTING KNOWLEDGE

More Printing Skills 02

Discover useful printing tips and improve your confidence with 3D printing.

PRINTING KNOWLEDGE

More Printing Skills 03

Expand your knowledge and explore more possibilities beyond your first few prints.

WE ARE HERE TO HELP

Still Need Help with Your AD5X?

If you encounter an issue that you are unable to resolve, please contact us via WhatsApp immediately.

Our team is here to help you troubleshoot your printer and get back to printing.

To help us assist you more efficiently, please include a photo or video of the issue, any error messages and relevant printing settings when contacting us.

WHATSAPP HARIMAU3D ↗